This week, I began to model my part of the complete pump - I would model the gauge read-out, the pipe connecting it to the junction, at which the regulators are connected, and then through to the hydraulic hose which monitors the level of fluid going into the regulators themselves
I wanted to begin by creating the pipe, so that I had a scaled object which I could then base all the other attachments by to keep the measurements accurate and not just have an excuse to use the 'Scale' tool!
By creating a 'Circle' and then converting to an 'Editable Poly', I could then use the option of 'Extrude Polygons Along Spline' to get the extruded material to follow a set path
I used the 'Line' tool to create a 'Spline' which, when set at 'Smooth' would create a consistent line without any angles or edges - I tried this keeping to scale first of all but this caused the vertices at the underside of the pipe where the pipe changes direction to invert themselves behind the row of vertices parallel to them, which meant there would be 'pinching' when applying any materials later on
I knew that this method would be the only way for the pipe to be constructed without extruding Polys all along the object itself and so I thought that by reverting the settings that generate the 'Spline' from 'Smooth' to 'Bezier' (as they were by default), I may be able to use the same method once more, but create a 'Spline' larger than real-life to avoid the curvature of its path to modify the vertices positions to the previous degree
The image below also shows that by increasing the number of 'Segments', or frequency of vertices that makeup the object, I could achieve a smoother finish (but unfortunately, this was to impact on the memory Max required to generate these modifications, so I had to abandon this idea too!)
The next step was to rotate the completed pipework 180degrees so that it could be compared easily against the reference photograph I was using during this process
Once it had been rotated, I noticed the circle from which I had 'Extruded' from was still open-ended, and so I had to select 'Border' from the 'Editable Poly' modifier, left-click onto the border/edge of the circle itself and then select the 'Cap' tool under the 'Edit Border' sub-heading under the modifier list - image above shows this
Having selected File>Merge>nut_bolt.max>Import Nut/Bolt, I now had both the nut and threaded bolt that I had created last week in this scene, ready to be cloned,modified and edited to create some of the obscure metalwork found throughout this iron-machine
My planning of keeping the scaling of each piece a prority paid off - here, I am able to drag the nut over the top of the pipework (also accurately scaled down from before) and find its just the right size!
After selecting the nut's polygons and using the 'Extrude' and 'Bevel' tools, I am able to generate washers and linkages that join each piece to another without creating each item seperately, which certainly increases the likelihood of the model being completed by the groups self-imposed deadline (only a couple of weeks, in reality)The threaded bolt was useful at this stage to become another part of the steam-control handle and fittings
By decreasing it in scale-length and increasing the number of 'length segments', it was possible to select the inner section of polygons and 'Bevel' them (by using the 'square icon' next to the name-tag, I could choose the amount by which the 'Polys' were 'Bevelled' in greater detail)
This attachment of the steam-control handle needed to be enlarged in the centre so, by using the 'Left' viewport, I then dragged-and-highlighted the 'Polys' that I wanted to scale up
(This method could also be employed with any object on this model-section that has been converted to an 'Editable Poly', although Id rather maintain an even scale when possible)
The pump should be modelled as accurately as Max would allow and this meant that if the pump had a fitting that had an impromptu hole through it, then thats what needs to be included in the model
Creating a to-scale cylinder and placing in through the relevant section, then choosing 'Boolean' from the 'Compound Objects' Object-Type, and selecting the fitting as 'Operand B' - the material where the cylinder sat has now been removed!By using a combination of all four viewports, I can assess the positions of the objects themselves as they being placed above or below each other on-screen. After adding on another nut attachment above the regulator-handle fitting (the modelling process of the handle itself will be further down), I was to create the gauge and inner dial, which was a 'Primitive Object' Cylinder reduced in height to '4.5cms' but increased in radius to '15cm' using the 'Parameter' options - I also increased the number of sides to 20 to ensure a smooth overall edge
After re-positioning the gauge to the angle shown in the reference images, I then went into 'Sub-Objec' level, selected 'Polygons' and highlighted all but the outer-most ring of them (adding to 140 Polygons!) - I then used the 'Move' tool and push in the Polys by about 4cms equivalent
This was so that I could then apply a material inside that would demonstrate the dial and all the detail in there and to then add a 'glass' cover over it with a simple 'Reflective' MapThe hands shown were created by using the 'Extended Primative' object 'Cone', with which I could then reduce the width and number of sides (the minimum is 3, unfortunately, so I couldn't get the shape totally flat) to get the desired form
Although I was dissapointed I couldn't get the shape to only have a single side, this threw up an unexpected advantage - why couldn't I use the three sides to not only display a 'Specular Highlight' as they went round to increase realism, but also to improve my judgement when animating to avoid them 'colliding' into the dial itself, whereas single sided there could be problems of that nature...
Before progressing any further, I wanted to sort out the 'dimpling' that appeared on the pipework at the underside where it changed direction, when it was extruded along the Spline 'Line' & extruded from the 'Circle' - this was perhaps due to acute angles that the the Line followed
The 'Front' view was very useful in allowing me to see 'inside' the model and modify the vertices and regularly check back in the 'Perspective' viewport how the re-postioning was affecting the mesh itselfHere you can see how, by careful manipulation of the vertices co-ordinates, I could realign them to get the underside smooth again
Having finished the modelling on the gauge/control end, I moved over to adding fittings and attachments to the opposite end if the pipe: this meant cloning a few copies of 'extruded nut_objects' and, as shown here, creating a scaled 'Cylinder' which would then be modified into the t-junction fitting that joins the hydraulic hose and its attachment rings, as well as the damping-taps to control the pressure of the compressed gas/steam coming into the pipes
To add extra detail to the 't-junction_object', I went into 'Sub Object Level', selected the Edges closest to the edge of the cylinder and brought them closer to the edge, adding in a bevelled edge to give a greater sense of the junction having properties close to that of its real-life counterpart
Note: Image should be rotated 180degrees!
This is the finished piece 't-junction_object', which means I have now linked up all three branches of this part of the whole model and I can now progress over to the hydraulic hose and then downwards to the casing (containing all the internal regulators and pistons, which thankfully we don't need to model!)
For some odd reason, I had completely missed the inclusion of the regulator handle
I knew it wasn't going to be an easy shape to replicate, attempting to create it by means of a 'cylinder', a 'cone' and even trying a 'spline' tool, but nothing came out particularly successfully
Then I thought about using the 'Sphere_Primitive Object' - I could convert it to an 'Editable Poly' and then select its vertices and manipulate them to achieve the desired shape, as shown here
Once I was happy with the scale of the handle itself, I then created the attachments that lead onto the regulator-control. The tap-fitting shown here and its bolt have valves inside to monitor the pressure that is released and this is then assessed by the dial above
Returning back to the 'hydraulic-hose' end of the pipe, all that was needed before I began the creation of the hose itself was a few more 'Extruded' and 'Bevelled' 'Nut_Objects' (to take the place of all the spacers and bushings between each section)
Then, it was simple case of scaling a 'Cylinder' to match the fittings in the vicinity - again, made easier by 'magnifying' the viewports of 'Front' and 'Top' so that all the outer 'Edges' were overlapping just slightlyTo make the hose, I conducted a similar method to how I first created the gauge-pipe - a 'Line' created under 'Splines', but this time I made sure it was described as 'Smooth' and 'Bezier' This was so that when I double-clicked after marking each marker along the 'path', I could bend the 'path' to flow and achieve a more accurate representation of the hose itself
Then I made another simple 'Circle Object', also done previously, and layered this next to the end of the cyclindrical connector-tube created in the caption/image above and got the circle to 'Extrude Along Spline'(segment rating of 50)
When I reached the cast-forged fitting which, while similar to the 't-junction' fitting above, had features that I felt were unable to be captured by a clone of that fitting, so I decided to use another 'Extended Primitive' and create the object using the 'Chamfer Cylinder'
Aaron of the group had used the 'Chamfer Box' before, so I knew its attributes could allow the object to be modified to a greater degree than just a 'Simple Primitive', like the 'Cylinder' or 'Box'
The main parameter I was interested in was the 'Fillet' tool - this meant that I could control the strength of the chamfer to cause the object to resemble a squat-looking gas-tank shapeAs I had intended, I was a case of choosing the 'Polygons' facing the direction I needed to go to follow the reference images and pulling the material out with the 'Move' tool (I tried the 'Scale' tool but this caused discrepancies in the 'mesh' of the object and could have possibly lead to the intended texture applied to distort - also similar complications with a UVW Map application!)
To create the 'Olive' attachment that is found on this fitting, I had to use the 'Donut' object
This is along the same lines as the 'Circle' Primitive Object, in so much as how I needed to convert to an 'Editable Poly' before it could be 'Extruded'! The object then needed to be repositioned over the previously 'Moved' selection of 'Polys' so that it followed the pump's real attributesThere was a process of then adding on the extra fittings and attachments to get to the Pressure Taps (to be created next week now), which included 'Cloning' of two more 'Nut Objects' and the addition of the 'Threaded Bolt' from the "nutbolt.max file" to become the bolt that holds these fittings together
The second of the two 'Cloned' nuts went onto the thread to complete this weeks modelling stage...*There is also the chance to trial some textures and apply some of my modified textures next week as a matter of course so that there are no real big suprises when I come to apply the material maps and styles to the objects before animation
This is obviously critical as I do not want to hold up the continual procedures our group has planned each and every meeting
I will present some examples of material/texture that will have a use on designated areas aorund the model next week*
No comments:
Post a Comment